AIRFLASH W/ STAND

BBC® AIR FLASH DRYER

A combined infrared and pass-through air dryer, the Air Flash Dryer by BBC Industries, Inc. is ideal for flashing or curing water-based or plastisol inks. This powerful dryer uses forced air. Holes spaced evenly across the infrared heater face create a remarkably level spread of air. A blower in the rear of the dryer provides a steady stream of air through to the T-shirt. Features Forced Air Pushes away moisture given off by the ink, which can absorb some of the heat given off by regular flash units Keeps the T-shirt slightly cooler, greatly reducing the possibility of scorching Built-In Solid-State Heat Control (permits settings from 0-100%; does not control strength of air) Magnetic Handle (can be placed anywhere on the Air Flash if running the dryer manually) Can Be Purchased with Flash-A-Matic™ or can be Purchased Separately

SUPER-TURBO, IR TEXTILE DRYER

The Super Turbo "E" Electric Forced Air Dryer is A.W.T.'s air dryer designed for efficient textile production. All plastisol and water based textile inks are cure-dried in the Super Turbo E at speeds up to 110 dozen pieces per hour -- or more. The design of this dryer includes a preheat chamber where the correct curing temperature of inks is quickly obtained. The preheat system can be air fired for energy efficient production. The Super-Turbo E has a quartz tube preheat zone. Heights of the preheat system inside the chamber are adjustable. The second section uses jet air-knives and high volume hot air to fully cure the textile ink while removing evaporates through the exhaust system. Re-circulating hoods re-circulate up to 90% of the dry airflow through the system. This helps to reduce your energy consumption. Dye fumes from colored shirts are safely exhausted. The Super Turbo G and GHO dryers keep textile production running smoothly and efficiently. Ink is fully cured with excellent results. Double insulated chambers allow air temperature to remain constant. This feature makes the dryer energy efficient with little heat loss. Temperatures for the quartz tubes/preheat zone can be set independently of the jet air. If air flow becomes restricted the heating system shuts down automatically and a safety alarm sounds. This safety feature keeps the blowers operating, preventing problems from scorching and blower burnout. Unit has full filter system. The fully modular construction makes expansion easy by simply adding heating or conveyor sections. Cat. No Description List Price Crating ST-361 Super-Turbo 36” Electric Textile Dryer, 5’ Heating Section, 34” Infeed and 24” Exit. 208-240V, 1Ph, 60Hz $7,995.00 $395.00 Larger Sizes Available

BIGRED DRYER-54" 4 HEATERS

Cure All Digital Inks, All Screen-printed Plastisol, and Water-based Inks and Discharge at Ultra-High Rates BigRed 4D Series dryers in 30 and 54 in. (76 and 137 cm) belt widths are the largest and most powerful dryers engineered specifically for DTG digital inks and/or screen-printed plastisols, water-based inks and discharge, making them ideal for Kornit® and other high-volume DTG shops, as well as automatic screen printing operations requiring high capacities. Model BR4D-V30 with a 30 in. (76 cm) wide belt and four 24 in. (61 cm) wide heaters (total 11,400 watts) cures 72 garments/h printed with DTG/digital white ink at 2.5 minutes dwell time, 216 garments/h with water-based ink or discharge, and 475 garments/h with plastisol ink. Model BR4D-V54 with a 54 in. (137 cm) wide belt and four 48 in. (122 cm) wide heaters (total 22,800 watts) cures 144 garments/h printed with DTG/digital white ink at 2.5 minutes dwell time, 432 garments/h with water-based ink or discharge, and 950 garments/h with plastisol ink. The capacity of both models can be doubled, tripled or quadrupled by adding one, two or three modular heating chambers and conveyor belt extensions — as new or when needs grow. For example, a model BR4D-V54 with four heating chambers can cure 576 garments/h printed with DTG/digital white ink at 2.5 minutes dwell time, 1,728 garments/h with water-based ink or discharge, and 3,800 garments/h with plastisol ink. All BigRed D Series dryers feature a high-powered pre-heating zone that surges ink temperatures past 300°F (149°C) within the first several inches of conveyor travel, maximizing dwell time at optimum curing temperatures and, in turn, conveyor belt speeds and dryer output. Air intake fans located below the roof of the enclosure quietly draw 'make-up' air into the chamber's double-walled shell through filtered inlets along opposite exterior sides at rates up to 560 cm (15.6 m3/min), serving to cool the outer shell for safety, while preheating the incoming air. An exhaust fan located below the center of the conveyor belt draws the preheated air downward at rates up to 900 cm (25.5 m3/min), over the garment and through the belt, removing heat, moisture, and contaminants from the chamber. To accommodate each shop's layout, the 6 inch (152 mm) diameter exhaust fan outlet rotates 360 degrees for connection to ductwork, and the control box can be located on the right (standard) or left side of the chamber. Exhaust filters located on both sides of the conveyor prevent garment lint from entering the blower or exhaust stack. Cleaning all filters before or after each shift can be accomplished in one minute, safeguarding printed images, the equipment, and the shop environment. Exhaust flow sensors with warning lights alert operators to a clogged exhaust line, clogged filter or blower failure. Other safety features include a light tower to monitor dryer status and a 'cool down mode' for powering down. Dual digital PID temperature controls maintain accuracy to +/-1°F (+/-0.5°C). The heaters of the BigRed 4D dryers carry a 15-year warranty and feature closely spaced coils that provide high-density, medium-wavelength infrared heat for maximum cure speed without cold spots or under curing associated with conventional units. FAST 475 - 950+ plastisol shirts/hr* 216 - 432+ water-based or discharge shirts/hr* 72 - 144+ DTG shirts/hr* with digital white ink SMARTUnique cooling bed at exit cools as garments exit the chamber SAFELight tower to monitor dryer status, a cool-down mode for easier shut-down and fault detection on the exhaust QUIETThe new BigRed 4D models are 20% quieter than earlier models ACCURATETemperature controller accurate to +/-1°F (+/-0.5°C) Digital PID with fuzzy logic — industry's most advanced ADJUSTABLEHand crank raises or lowers all heating chambers simultaneously to within 2" - 7" (5 - 17.7 cm) of the belt for bulky items or hats CONVENIENTDigital belt speed voltmeter — a must-have VERSATILEMake-up Air and Negative Exhaust Air — removes moisture and fumes ultra-fast FILTEREDFiltered air intake prevents dust contamination of images. Filtered exhaust prevents garment lint from entering the blower or exhaust stack HEAVY-DUTY"X-Series" Conveyor Belt Tracking System BELT WIDTH(Maximum garment width)30" (76 cm) or 54" (137 cm) HEATER WIDTH24" (61 cm) or 48" (122 cm) MAXIMUM IMAGE WIDTH18 in. (46 cm) or 42 in. (107 cm)(Heater width minus 6 in. [15 cm]) EXPANDABLEAdd heat chambers and belt extensions OPTIONS Heating chambers @ 54 in. (137cm) long Belt extensions, front or rear @ 18 in. (46 cm) long The control box on left side (right side standard) 3 Phase and 208, 380, 480 voltages Exhaust hood for extra fume extraction Hat support rail Locking casters for mobility Heavy-duty motor drive for conveyor belts Donut probe Additional heater clearance.

BBC® DIGI-DRI PORTABLE INFRARED DRYER

The Digi-Dri™ Portable Infrared Dryer from BBC Industries, Inc. is your answer to printing faster on your large format printer. It conveniently rolls up to your printer and gently dries the ink to a full cure. Its flexible design and uniform heat distribution gently full cures inks without any circulating air. The Digi-Dri™ is safe for all inks and substrates. The Digi-Dri™ Portable Infrared Dryer includes an on/off switch, solid-state temperature control, a 10-foot cord with plug (except 220 V units), and casters. Digi-Dri™ Portable Infrared Dryer Features Portable from One Printer to Another Immediate Drying of Printed Media without Air Uniform Heat Distribution Across Entire Surface Safe for All Inks and Substrates Flexible Design – Adjustable Height, Angle, Tilt of Heater Solid-State Temperature Controller Available in 36 in, 54 in, 64 in, 72 in, and 108 in Standard Sizes All Sizes Available in 120 V and 240 V Models Optional Auto Shutoff Allows Dryer To Be Turned Off at Estimated End of Print Run Maneuverable Stand with 30-Degree Adjustable Incline/Decline Add a Second Heater head for Printing at even Higher Speeds All 220V Units are CE Certified 1 Year Warranty Auto Shut Off Assembly Stand Assembly

BIGRED DRYER 4D - 30" & 54"

BigRed® 4D Series dryers in 30 and 54 in. (76 and 137 cm) belt widths are the largest and most powerful dryers engineered specifically for DTG digital inks and/or screen-printed plastisols, water-based inks and discharge, making them ideal for Kornit® and other high-volume DTG shops, as well as automatic screen printing operations requiring high capacities. Model BR4D-V30 with a 30 in. (76 cm) wide belt and four 24 in. (61 cm) wide heaters (total 11,400 watts) cures 72 garments/h printed with DTG/digital white ink at 2.5 minutes dwell time, 216 garments/h with water-based ink or discharge, and 475 garments/h with plastisol ink. Model BR4D-V54 with a 54 in. (137 cm) wide belt and four 48 in. (122 cm) wide heaters (total 22,800 watts) cures 144 garments/h printed with DTG/digital white ink at 2.5 minutes dwell time, 432 garments/h with water-based ink or discharge, and 950 garments/h with plastisol ink. Deluxe models come as standard with adjustable side-mounted heaters that increase the "cure zone" to 24 inches on the EC III-30 and to 48 inches on the EC III-54. Other standard features on the deluxe model include heavy-duty drop down wheels for easy shop mobility and an 18 in. (46 cm) front conveyor extension that provides additional room for loading garments on the belt. Capacity of all models can be doubled, tripled or quadrupled by adding one, two or three modular heating chambers and conveyor belt extensions — as new or when needs grow. For example, a model BR4D-V54 with four heating chambers can cure 576 garments/h printed with DTG/digital white ink at 2.5 minutes dwell time, 1,728 garments/h with water-based ink or discharge, and 3,800 garments/h with plastisol ink. All BigRed D Series dryers feature a high-powered pre-heating zone that surges ink temperatures past 300°F (149°C) within the first several inches of conveyor travel, maximizing dwell time at optimum curing temperatures and, in turn, conveyor belt speeds and dryer output. Air intake fans located below the roof of the enclosure quietly draw 'make-up' air into the chamber's double-walled shell through filtered inlets along opposite exterior sides at rates up to 560 cfm (15.6 m3/min), serving to cool the outer shell for safety, while preheating the incoming air. An exhaust fan located below the center of the conveyor belt draws the preheated air downward at rates up to 900 cfm (25.5 m3/min), over the garment and through the belt, removing heat, moisture and contaminants from the chamber. To accommodate each shop's layout, the 6 inch (152 mm) diameter exhaust fan outlet rotates 360 degrees for connection to ductwork, and the control box can be located on the right (standard) or left side of the chamber. Exhaust filters located on both sides of the conveyor prevent garment lint from entering the blower or exhaust stack. Cleaning all filters before or after each shift can be accomplished in one minute, safeguarding printed images, the equipment and the shop environment. Exhaust flow sensors with warning lights alert operators to a clogged exhaust line, clogged filter or blower failure. Other safety features include a light tower to monitor dryer status, and a 'cool down mode' for powering down. Dual digital PID temperature controls maintain accuracy to +/-1°F (+/-0.5°C). The heaters of the BigRed 4D dryers carry a 15-year warranty, and feature closely spaced coils that provide high-density, medium-wavelength infrared heat for maximum cure speed without cold spots or under curing associated with conventional units. Features Fast 475 - 950+ plastisol shirts/hr* 216 - 432+ water-based or discharge shirts/hr* 72 - 144+ DTG shirts/hr* with digital white ink SmartUnique cooling bed at exit cools as garments exit the chamber SafeLight tower to monitor dryer status, cool-down mode for easier shut-down and fault detection on the exhaust QuietThe new BigRed 4D models are 20% quieter than earlier models AccurateTemperature controller accurate to +/-1°F (+/-0.5°C) Digital PID with fuzzy logic — industry's most advanced AdjustableHand crank raises or lowers all heating chambers simultaneously to within 2" - 7" (5 - 17.7 cm) of the belt for bulky items or hats. Models with side heaters can be adjusted from 4 to 7 in. (10 - 17.8 cm) from belt to heater. ConvenientDigital belt speed voltmeter — a must have VersatileMake-up Air and Negative Exhaust Air — removes moisture and fumes ultra-fast FilteredFiltered air intake prevents dust contamination of images. Filtered exhaust prevents garment lint from entering the blower or exhaust stack Heavy Duty"X-Series" Conveyor Belt Tracking System Belt Width(Maximum garment width)30" (76 cm) or 54" (137 cm) Heater Width24" (61 cm) or 48" (122 cm) Maximum Image Width18 in. (46 cm) or 42 in. (107 cm)(Heater width minus 6 in. [15 cm]) ExpandableAdd heat chambers and belt extensions Modular expandability allows your dryer to grow with you The capacity (belt speed) of all Vastex floor standing conveyor dryers can be doubled or tripled as new or when needs increase by simply adding one or two modular heating chambers and extending the conveyor belt. This eliminates the need to invest in a larger dryer than you need at the onset, and avoids the high cost of purchasing a new dryer when your needs increase. Options Additional heating chambers @ 54 in. (137cm) long Belt extensions, front or rear @ 18 in. (46 cm) long Side heaters to increase "cure zone" Control box on left side (right side standard) 3 Phase and 208, 380, 480 voltages Exhaust hood for extra fume extraction Hat support rail Locking casters for mobility Heavy duty motor drive for conveyor belts Donut probe Additional heater clearance Documents Brochure Operation Manual

D1-SERIES D-100 DRYER

Entry level tabletop dryer with 18" (45.7 cm) wide conveyor belt cures up to 110 plastisol-printed garments/h, 50 discharge-printed garments/h, and DTF adhesives at high rates. Adjustable heater height/angle, heat intensity and belt speed provide full operator control. 120V and 240V models with optional powered exhaust remove moisture and fumes — critical for rapid drying of water-based inks and discharge, and curing of DTF adhesives. SMART PTFE coated fiberglass belt with tracking system BELT WIDTH(max garment width) 18" (46 cm) HEATER WIDTH 16" (41 cm) ADJUSTABLE Speed, temperature, heater height and tilt FAST 110+* shirts per hour with plastisol and 50+* with discharge PRECISE Powerful infrared heater with tight coil pattern and heat shields VALUABLE Best warranty, high quality, exceptional service COMPACT Total footprint is less than 8 sq.ft (2.44 sq.m) OPTIONS Optional powered exhaust removes moisture and fumes — ideal for working in confined spaces, especially when curing of DTF adhesives. Optional stands with wheels. Brouchure & Specifications Operation Manual

LITTLERED XD DUAL ZONE - 30", 54" & 78"

X1D is the smallest conveyor dryer matched to the output of the most popular DTG printing systems. Its heating chamber has a boost zone to quickly reach cure temperatures for ink jet, water-based and discharge inks. The LittleRed X1D-18 with an 18 in. (46 cm) wide conveyor belt has a heating chamber the full width of the belt, and can dry Digital White Ink at rates up to 34 pieces per hour at 2 minutes dwell time, or up to 81 garments/hr with water-based ink or discharge, and cure up to 162 garments per hour with plastisol ink. The LittleRed X1D-30 with a 30 in. (76 cm) wide conveyor belt features a 24 in. (61 cm) wide heater and can dry Digital White Ink at rates up to 29 pieces per hour at 2 minutes dwell time, or up to 65 garments/hr with water-based ink or discharge, and cure up to 150 garments per hour with plastisol ink. It eliminates the flattened, ironed-on appearance and halo associated with heat pressing of printed images, and relegates the heat press to flattening of raised fibers prior to printing with a one second 'touch' per garment. As standard it is equipped with features found on the company's larger DTG capable dryers including adjustable belt-to-heater clearance to accommodate bulky items, a dual digital PID temperature controller accurate to +/- 1°F, and an X-Series conveyor belt roller tracking system with PTFE coated fiberglass belt. A powered exhaust removes moisture and air contaminants, while cooling the housing and controls. The LittleRed™ X2D Dryer is the most compact and affordable DTG-capable dryer from Vastex. Radically new heat mapping speeds the curing of ink jet, water-based and discharge inks, as well as DTG-digital inks, making the X2D an unbeatable value for smaller shops. The X2D model comes with a high powered pre-heating zone that surges ink temperatures to over 300°F (149°C) within the first several inches of conveyor travel inside the 27 in. (69 cm) heating chamber. Two closely spaced, height adjustable infrared heaters and dual zone heat controls maintain consistent temperatures needed for DTG and all other inks. Rapid preheating maximizes the dwell time for each kind of ink, allowing increased conveyor belt speeds and dryer output. Model X2D-30 has a 30 in. (76 cm) wide belt, two 24 in. (61 cm) wide infrared heaters (6300W @ 240V total wattage), and cures up to 240+ garments per hour with plastisol inks, up to 122+ garments per hour with water-based inks, and up to 34 garments per hour with DTG/digital white ink at 3 minutes dwell time. This model comes with a powered exhaust system as standard to rapidly remove moisture and air contaminates from the heating chamber, as well as to cool the skin and controls. The conveyor length is 66 in. (168 cm), with a low friction belt aligner and belt speed controls to precisely set dwell times from 35 seconds up to four minutes. Fully expandable, additional heating chambers and conveyor belt lengths allow for future expansion as business grows. The heaters of all Vastex dryers carry an industry-leading 15-year warranty, and feature closely spaced coils to provide high-density, medium-wavelength infrared heat for maximum cure speed without cold spots or under curing associated with conventional units. The multi-purpose LittleRed X3-D infrared dryer cures direct-to-garment (DTG) printed textiles as well as plastisol, water-based and discharge-printed garments at higher rates than possible with conventional dryer designs. Available in 30, 54 and 78 in. (76, 137, and 198 cm) belt widths, it features a high-powered pre-heating zone that rockets ink temperatures past 300°F (149°C) within the first several inches of conveyor travel, maximizing the distance and dwell time for optimum curing of any ink, allowing increased conveyor belt speeds and dryer output. The Little Red X3-D-30 model is equipped with a 30 in. (76.2 cm) wide conveyor belt and three 24 in. (61 cm) wide infrared heaters (8900W @ 240V total wattage) and can cure 360+ plastisol-printed garments/h, 185+ water-based or discharge-printed garments/h, and up to 51+ garments/h inkjet printed with digital white ink at 3 minutes dwell time. The 54 in. (137 cm) wide LittleRed X3-D-54 model cures 720+ plastisol-printed garments/h, 370+ water-based or discharge-printed garments/h, and 103+ garments/h inkjet printed with digital white ink or pretreated for DTG printing at 3 minutes dwell time. The 78 in. (198 cm) wide LittleRed X3-D-78 model accommodates up to three rows of garments, and cures a whopping 1080+ plastisol-printed garments/h, 555+ water-based or discharge-printed garments/h, and 155+ garments/h inkjet printed with digital white ink or pretreated for DTG printing at 3 minutes dwell time. The X3-D-30 and X3-D-54 models have an overall conveyor belt length of 88 in. (224 cm) long while the X3-D-78 model has an overall length of 102 in. (260 cm). The heating chamber for all three models is 41 in. (104 cm) long and features a powerful, targeted exhaust system as standard to rapidly remove moisture and air contaminates from the heating chamber, as well as cool the skin and controls. With a second X3 chamber, the LR-X3D-30-2 and LR-X3D-54-2 can handle higher production including longer times necessary for Kornit printers. FLEXIBLECan cure plastisol, water-based, discharge and inkjet-printed white ink in record time POWERFUL LittleRed X3D-30 has 8900W@240V total wattage LittleRed X3D-54 has 17,800W@240V total wattage LittleRed X3D-78 has 26,700W@240 total wattage DEPENDABLEIndustry-leading 15-year heater warranty EFFICIENTClosely spaced coils provide high-density, medium-wavelength infrared heat for maximum cure speed without cold spots or under-curing FAST LittleRed X3D-30360+ garments/hr for plastisol inks, 185+ garments/hr for water-based or discharge inks, 51+ garments/hr for DTG digital white ink @ 3 minutes, 61+ garments/hr @ 2.5 minutes LittleRed X3D-54720+ garments/hr for plastisol inks, 370+ garments/hr for water-based or discharge inks, 123+ garments/hr for DTG digital white ink @ 3 minutes, 103+ garments/hr @ 2.5 minutes LittleRed X3D-781080+ garments/hr for plastisol inks, 555+ garments/hr for water-based or discharge inks, 185+ garments/hr for DTG digital white ink @ 3 minutes, 155+ garments/hr @ 2.5 minutes CONSISTENTLow friction belt aligner and DC belt speed control with digital display HEAVY DUTY"X-Series" Conveyor Belt Roller Tracking System with PTFE coated fiberglass belt and HD belt motor ACCURATEDual digital PID Temperature controller is accurate to +/-1°F ADJUSTABLE2 - 7 in. (5 - 18 cm) belt-to-heater clearance, adjustable separately on each side for each heater EXPANDABLEAdd additional chambers and belt extensions OPTIONS Additional heating chambers and conveyor belt extensions Locking casters for mobility Creeper gear Brochure and Specifications Operation Manual

REDFLASH W/ STAND

STANDARD FEATURES Adjustable Heat Control Casters Included 15 Year Heater Warranty 3 Year Bumper to Bumper Warranty Head rotates 360° 18" x 18" or 18" x 24" models available User friendly diagnostic pilot lights Convenient heavy-duty side handles Low profile 2 3/4" head height Adjustable height 240 volt models available Low cost maintenance Vented heat shield Anti-rust treatment on all painted steel Flash plastisol in 7-10 seconds RELIABLE 15 Year Heater Warranty POWERFUL3500 Watt heater USER FRIENDLYDiagnostic pilot lights & heat control CONVENIENTHeavy duty side handles & locking casters EFFICIENTHigh wattage and high heater density FASTESTHO heater flashes plastisol in as little as 4sec UNIQUEHead leveler, cooling fan and air curtains THIN PROFILEUltra slim 2.75" (7 cm) height head REQUIRED OUTLETS R-18-240 6-15R R-18-240-HO/ R-1824-240 6-20R MODELS AVAILABLE R-18-240: 18 x 18"; 240V; 2600 Watt R-18-240-HO: 18 x 18"; 240V; 3500 Watt R-1824-240: 18 x 24"; 240V; 3500 Watt AutoFlash automatic head swing OPTIONS AutoFlash automatic head swing Super Heavy Duty stand Adjustable Heat Control Manual Brochure