Nylon White Plastisol Ink is our most versatile bleed-resistant white — a high-opacity white that prints on nylon, polyester, 100% cotton and blends, direct or as an underbase, blocking dye migration so it stays clean and bright. On nylon it bonds with the required catalyst. Cures at 290–300°F. CPSIA-compliant and phthalate-free, made in Hackensack, New Jersey.

Pint through 5 gallon. Heat cure. Made in the USA.

⚠ Printing on nylon? Add the catalyst. For nylon, mix in Nylon Bond 289 Additive so the ink bonds to the fabric. On cotton, polyester and blends, no catalyst is needed.

Also available in larger quantities — 30-gallon and 55-gallon drums; call 201-487-9600 for volume and discount pricing.

Features & benefits

Prints nylon, polyester, cotton & blends — one bleed-resistant white for nearly any garment
Bonds to nylon — with Nylon Bond 289 catalyst, adheres to slick nylon
Bleed-resistant — blocks dye migration so the white stays bright
High opacity — bright, dense coverage; direct print or underbase
Creamy & print-ready — smooth lay-down on manual or automatic presses
Pint to 5 gallon (plus 30 & 55 gallon drums)
CPSIA-compliant & phthalate-free — made in the USA

Always run a test print first. Before any production run, print and fully cure a test on your exact garment — for nylon use catalyzed ink and check adhesion with a stretch and wash test, plus opacity and dye migration. It's the best habit in the shop — if you're not sure on settings, call us at 201-487-9600 before you run the job.

What it prints on

Nylon — jackets, bags, activewear; mix in Nylon Bond 289 for adhesion
Polyester — bleed-resistant; holds back dye migration (no catalyst)
100% cotton & blends — bright white, direct print or underbase (no catalyst)

Printing & curing

Catalyst: for nylon, add Nylon Bond 289 per its mix ratio; use catalyzed ink within its pot life
Mesh: 110–160 for maximum opacity; up to 200+ for a lighter deposit
Squeegee: 65, 75 or 80 durometer — or a 70/90/70 triple durometer
Flash: 240–260°F when used as an underbase; keep flash low and brief on synthetics
Cure: curing is a time-and-temperature process — bring the full ink film to 290–300°F (143–149°C); confirm with a temp gun or donut probe, not dryer air temp

Recommended companion products

Nylon Bond 289 Additive — required for nylon adhesion; mix into the ink before printing.
Quick Flash Reducer — thins for easier printing.
Soft Hand Base — softer hand feel.
Cleanup: OPTI Wash 125 and OPTI Spot 303.

How close are we to your Pantone?

See our Standard Color → Pantone® (PMS) Match Chart — the closest Pantone® reference for every Total Ink Solutions standard color, with RGB and HEX values. For an exact, verified match, our UMX® system mixes to your target.

Safety, PPE & storage

Wear nitrile gloves and safety glasses; avoid prolonged skin contact with uncured ink.
Print with adequate ventilation; vent your dryer.
Always stir before use.
Storage & shelf life: keep sealed, out of sun. Shelf life 1–2 years. In high heat expect container expansion — open carefully. Do not freeze.
Refer to the Safety Data Sheet before use.

Compliance

CPSIA compliant (16 CFR 1303 <90 ppm; CPSIA §101 <100 ppm total lead) — safe for children's apparel. Phthalate-free.

⚠ WARNING (California Proposition 65): This product can expose you to chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

Questions?

Total Ink Solutions
200 South Newman Street, Unit 4 & 5
Hackensack, NJ 07601
Phone: 201-487-9600 · Fax: 201-487-9620
Email: sales@totalinksolutions.com

Nylon Plastisol Ink

Nylon Plastisol Ink