Athletic White Polyester Plastisol Ink - 100% Polyesters

Athletic White Polyester Plastisol Ink is a high-opacity, low-cure white engineered for 100% polyester and spandex — a bright, dense white that prints direct or lays down as a bleed-resistant underbase, its dye-blocking chemistry and low cure stopping polyester dyes from migrating or ghosting through. The super-stretch film flexes with performance fabric without cracking. CPSIA-compliant and phthalate-free, made in Hackensack, New Jersey.

Pint through 55 gallon. Heat cure. Made in the USA.

Also available in larger quantities — 30-gallon and 55-gallon drums; call 201-487-9600 for volume and discount pricing.

Features & benefits

• Bleed-resistant dye-migration blocker — stops polyester dyes from ghosting into your white
• Super-stretch — flexes with spandex and performance fabric without cracking
• Low cure (290–310°F) — runs cool to protect heat-sensitive poly and save energy
• Maximum opacity — bright, dense white; direct print or a dependable poly underbase
• Creamy & print-ready — smooth flow on manual or automatic presses
• Pint to 55 gallon — stock sizes plus drums for production shops
• CPSIA-compliant & phthalate-free — safe for kids' apparel, made in the USA

Always run a test print first. Before any production run, print and fully cure a test on your exact garment and check opacity, hand, dye migration and wash-fastness. It's the best habit in the shop — if you're not sure on settings, call us at 201-487-9600 before you run the job.

What it prints on

• 100% polyester — jerseys, performance tees, athletic wear
• Spandex & performance blends — the super-stretch film moves with the fabric
• Poly blends & sublimated garments prone to dye migration — runs as a bleed-blocking white underbase

Printing & curing

• Mesh: 110–160 for maximum opacity; up to 200+ for a lighter deposit
• Squeegee: 65, 75 or 80 durometer — or a 70/90/70 triple durometer
• Flash: 240–260°F; keep flash low and brief to avoid triggering dye migration
• Cure: curing is a time-and-temperature process — bring the full ink film to 290–310°F (143–154°C); the low cure is what keeps polyester dyes from bleeding; confirm with a temp gun or donut probe, not dryer air temp

Recommended companion products

• Nylon Bond 289 Additive — mix into this ink to bond prints to nylon and other slick synthetics (catalyst; stir in a small amount, limited pot life, always test first).
• Quick Flash Reducer — thins for easier printing.
• Soft Hand Base — softer hand feel.
• Pantone® Custom Color Match — send us your target Pantone® and we custom-mix the color for you (plastisol, solvent, UV & water-base).
• Cleanup: OPTI Wash 125 and OPTI Spot 303.

How close are we to your Pantone?

See our Standard Color → Pantone® (PMS) Match Chart — the closest Pantone® reference for every Total Ink Solutions standard color, with RGB and HEX values. For an exact, verified match, our UMX® system mixes to your target.

Safety, PPE & storage

• Wear nitrile gloves and safety glasses; avoid prolonged skin contact with uncured ink.
• Print with adequate ventilation; vent your dryer.
• Always stir before use.
• Storage & shelf life: keep sealed, out of sun. Shelf life 1–2 years. As an all-polyester low-cure ink, store at 60–80°F. In high heat expect container expansion — open carefully. Do not freeze.
• Refer to the Safety Data Sheet before use.

Compliance

CPSIA compliant (16 CFR 1303 <90 ppm; CPSIA §101 <100 ppm total lead) — safe for children's apparel. Phthalate-free.

⚠ WARNING (California Proposition 65): This product can expose you to chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

Questions?

Total Ink Solutions
200 South Newman Street, Unit 4 & 5
Hackensack, NJ 07601
Phone: 201-487-9600 · Fax: 201-487-9620
Email: sales@totalinksolutions.com